
Inside and out, it can be tempting to think that a used Ford truck is clean and well maintained. But, underneath, there can be a whole other problem one of the main concerns with buying used pickup is rust. Although it may look like the problem has only been associated with the paintwork, rust can also creep into the frame, mounting brackets, suspension parts and so on and covering up with a new coat of paint isn’t always enough.
Apply a close eye to trucks operating in environments where winter road salt is prevalent especially around the underbody and inside enclosed metal areas. There is often moisture, mud, road dirt, and even salt buildup lurking where you can’t easily see it during a walkaround. Spotting corrosion before buying a truck will save you thousands down the road, but more importantly, inspecting these areas can tell you what sort of shape the truck is in when it comes to everyday use, towing, or tough work.

1. Rocker Panels
You’ll find rocker panels down low underneath the cab doors and along the entire edge of the truck cabin. Because they’re located so low, they often get hit by water, dirt, mud, and salt spray from the tires. Water can sometimes pool in the panel and cause it to corrode from the inside out, long before anything shows up on the outside. Even a truck that looks like new may be hiding a significant amount of damage below the surface along the lower edge of the cabin.
Rocker Panel Inspection Checklist:
- Check both sides carefully
- Look for bubbling paint
- Feel for soft metal
- Watch for suspicious fresh undercoating
- Check previous body repairs
Drop to the ground and look under the truck along the full length of each rocker panel in the daylight. Look for rippled surfaces, soft spots, bubbling paint and panels that look like they have been patched recently. If you find shallow and deep dents, and use a small magnet to see if thick body filler is concealing the damage to the steel. Don’t overlook rocker corrosion, either. As the panels weaken, they might diminish the integrity of the cab in a side impact, and the panels may no longer provide reliable support when the truck is lifted with a jack.

2. Cab Corners
Cab corners At the back of the Crew Cab behind the rear doors and behind the seats on a Regular Cab. Both areas are “trapped” sections where road trash, salt and moisture can accumulate in a sealed-off pocket. Once the water gets in, it can keep on rusting underneath the paint layer until you see rust stains bleeding through the paint. The metal beneath the primer may have been compromised long before you ever see rust on the surface of an old Ford.
What to Look For Around Cab Corners:
- Inspect both lower corners
- Feel for rough patches
- Check for uneven bodywork
- Look for paint mismatches
- Keep drain openings clear
Go around both cab corners with your hand and feel for any ripples or rough textures, bumps, or unusual softness compared to the rest of the panel. A new coat of paint and a subtle color variation may be all that is left of rust repair. Also, make certain that the drain holes at the bottom of the panel are clear so that water will drain out of the inside of the corners. Clogged drains trap moisture, which can lead to corrosion. Don’t buy into the “post-repair” appeal of the panels you could pay dearly down the line.

3. Frame Rails
Frame Rails Everything else rides on top of the frame rails, which are the main frame of a pickup, giving the truck a significant portion of its strength. They bear a load when driving, tow and haul, so any rust isn’t easy to ignore. Older trucks tend to have a mild light orange tint to the frame rails, but heavy scale and flaking, holes and soft spots are concerning and can show signs of corrosion that has penetrated far below the surface. Severe frame damage can impact everything from the truck’s ride and towing capacity, to its crashworthiness.
Frame Areas That Need Attention:
- Follow both rails underneath
- Inspect welded joints closely
- Check around crossmembers
- Look for deep metal scaling
- Watch for crumbling steel
Use a bright flashlight to examine each side of the frame from the front bumper all the way back to the end of the truck. Pay close attention to the welding joints, crossmembers, steering components and fuel tank supports. Dirt and moisture can gather in these areas. Use a small hammer or screwdriver to probe suspicious areas. Healthy steel will feel solid while crumbling flakes, soft patches and a dull tone indicate serious deterioration. Never dismiss heavy rust as simply age. If the frame is damaged, have it evaluated by a professional before buying.

4. Bed Crossmembers
Bed crossmembers provide support under the truck bed for carrying heavy loads, and they also contribute to the overall integrity of the truck’s frame. These supports are situated underneath the bed, leaving them vulnerable to dirt, water, and debris that are kicked up and spat out by the wheels when you’re driving down the road. If your truck sees heavy workday use, or you load your truck’s bed frequently, these supports can take a hit over time, rusting away. The other thing to keep in mind is that they are not visible in any way from the outside of the truck bed, so you could have a clean bed but a rusty support system.
Bed Crossmember Inspection Points:
- Examine every visible crossmember
- Check for cracked welds
- Look for holes
- Watch for sagging supports
- Inspect bed mounting points
Get under the rear bumper with a flashlight, and check the crossmembers one by one. A little superficial surface discoloration in an older pickup might be normal, but serious scaling, holes, cracked welds, and warping of metal all should be more thoroughly investigated. Don’t forget the mounting points between the cargo bed and the chassis frame. Any moisture caught between these may cause serious corrosion over time. Weakening mounting points can cause the bed to droop during towing or when carrying heavy cargo, so double check to make sure it’s all still intact before you buy.

5. Brake and Fuel Lines
Brake and fuel lines are always along the sides of the chassis frame and are easy to overlook when you’re viewing the truck from outside. They are thin steel tubes that sit exposed to salt, mud, water, and winter weather year-round. Rust accumulates in the form of small pits that lead to moisture weakening the metal. From a distance, it is possible that the lines don’t show much rust, but they can be corroded in hidden areas and at fittings, which warrants close inspection because any compromise can be problematic once the truck is back in service.
Important Line Inspection Checks:
- Follow lines from front to rear
- Look for flaking metal
- Check for damp patches
- Inspect repaired sections carefully
- Watch for compression fittings
Follow the brake and fuel lines down the frame rails with a flashlight, inspecting both sides to the extent possible. Feel for irregular surface, heavy rust flakes, moisture from wet spots, and two pieces joined with compression fittings that might have been used to make repairs in the past. Severe rust may break or compromise a brake line causing a sudden brake failure. Leaking fuel lines are a fire hazard, also. Never assume the truck is safe because the brakes and engine seem to be operating normally on a short test drive. Check questionable lines at the time of sale.

6. Wheel Wells and Inner Fenders
Make sure to look inside the wheel wells for deterioration. The tires beat against the inner fenders every time you drive and can cause factory finishes to eventually degrade. These prime areas for corrosion over time, particularly around all of the body joints that can be hard to see if it’s hidden behind the wheel liner. Many vehicles build up debris around the rolled edges of the openings and can hide rust behind the liner that isn’t always visible without a closer look.
Wheel Well Areas to Examine:
- Inspect inner fender panels
- Turn front wheels fully
- Check folded metal edges
- Look for packed dirt
- Question fresh undercoating
Crank the front wheels to one side to better see inside panels, suspension perches and bend-up sheet-metal edges. In back, shine a flashlight into the wheel wells and run your hand along any rust streaks or bubbling paint. Dirt packed in tight to the surface traps moisture, which can eat away at the metal below the primer or coating. Keep an eye out for fresh patchy undercoating or seam sealer that may have been sprayed over rotted areas. Once inside framing points rust away, repairs often require chopping out the damaged area and welding in new panels-a total pain, and costly.

7. Suspension Mounting Points
Suspension mounting points are the places where the main suspension components and other critical mechanical items are mounted on your truck frame. These points include brackets for your leaf springs, axles, sway bars, shocks, and control arms. These mounting points must be strong enough to support the entire weight of your suspension system along with the stresses placed on the suspension system, which are, braking, acceleration, turning and towing duty. When grime, road grit and moisture get trapped in overlapping metal plates, rust can form and take out a suspension mounting point. Rusted mounting points can cause serious suspension system problems and may require more than routine maintenance.
Suspension Mounting Inspection Checklist:
- Check rear leaf spring hangers
- Inspect shackles and brackets
- Look for cracked welds
- Watch for separating metal
- Question freshly painted mounts
Grab a flashlight and take a look at the back leaf spring hangers and shackles, which are under a lot of stress during acceleration, braking and towing. Be aware of any heavy pitting, flakes of rust, cracked welds and flaking metal at the mounting bolts. Look for puddles of dirt and water in corners of brackets and between overlapping steel plates. Sometimes newer black paint or selective spray-down around suspension brackets can hide weakened metal. Don’t overlook these clues just because truck runs well. Rusted and flaking metal that loses suspension mount hardware can lead to shifted parts and costly frame welding or structural repairs down the road.

8. Door Bottoms and Drain Holes
You may notice that the bottom of your truck doors has some rust, despite the exterior paint still looking fresh. Moisture can drain between the outer glass and into the shell of your door which contains tiny drain holes to let water escape. The problem is, those holes can get filled with road dirt, leaves and other debris, trapping the water inside the door and resulting in corrosion to the metal below. Before you buy a used pickup, be sure to check out the lower door edges and drains.
Door Rust Checks Before Buying:
- Open every door fully
- Inspect lower inner edges
- Feel for swollen metal
- Check all drain openings
- Look for loose rust flakes
Open all the doors to the extent possible, and run your hand along the lower lip of the interior of a door. Is there any signs of rust, any swelling of the metal or paint? Look down the drain passages and at the access holes for the hinges with a flashlight. Drain holes should be kept clear so the rain will run out of the door shell instead of just sitting in the door’s interior side. Dusty flakes of loose rust at drain holes may be indicative of rust weeping behind the paint. Full door shell replacement costs can be extremely expensive, so it’s worth a few minutes to look for potential trouble spots.

9. Rear Bumper Mounts and Hitch Receiver
There’s also more road spray, mud, winter brine and grit being flung up from the wheels behind the rear end of pickups. That makes the bumper brackets and hitch receiver more prone to corrosion. They’re also more than accessories, because they’re used to tow trailers and to carry cargo, and they’re used as anchor points for gear or mounts on the vehicle’s frame. Heavy corrosion can start at those attachment points and remain hidden, even though you can’t see through the hitch from behind.
Rear-End Inspection Points:
- Check inside the hitch receiver
- Inspect bumper mounting brackets
- Look for cracked welds
- Examine frame attachment points
- Question fresh paint patches
Hold up a flashlight behind the hitch receiver tube and look for heavy scaling, deformed steel, cracked welds and over-rotated attachment points. Next, take a closer look at the mounting brackets for the rear bumper to the frame of the vehicle where two pieces of metal come into contact. Rainwater and other moisture collected between the two sections can cause corrosion that is hard to pick up on the outside. Also, look for fresh paint around the receiver tube or along frame horns, both of which experience heavy loads during towing and mounting, which may hide previous damage.
10. Spare Tire Carrier and Rear Crossmember
Located below the truck bed, the spare tire carrier and rear crossmember are subject to a lot of dirt, moisture and road salt, without being noticed. In addition, the spare tire itself can harbor moisture against the mounting winch, cables and other metal parts. Because the spare tire and crossmember are not easily visible at the time of an inspection, you could end up with rust and corrosion for years before you ever realized a problem was there. Besides, the rear crossmember has a critical structural function that needs to be reviewed before buying a secondhand pickup.
Final Underbody Checks:
- Ask seller to lower spare
- Test the winch mechanism
- Inspect rear crossmember carefully
- Check for fractured welds
- Look for perforated metal
Have the seller loosen the spare so you can try out the winch mechanism to see if it frees or is frozen from corrosion. Then take a good look at the carrier hardware, rear crossmember and adjacent frame rails. Look for flaking and peeling metal, holes and open or broken welds. Also have a good look at the areas supporting any hitch assemblies or bumper mounts. If the rear crossmember is heavily corroded, you might not be able to buy a simple replacement, but will need to have an extensive amount of welding work done to regain strength. Do a careful walk-around before buying to avoid a pricey repair later.
